Pneumatic valve, driven by compressed air valve, the valve closed, the sealing surface can only rely on media pressure to seal, that media pressure will depend on the sealing surface of the ram pressure to the other side of the seat to ensure the sealing surface of the seal, which is self sealing. Most of the valve is forced to seal, that is, when the valve is closed, to rely on external force to force the gate to the seat, in order to ensure the sealing surface of the seal
Note: parameters are for reference only, or are not full. Valve can be used in accordance with the requirements of different pressure, material, diameter, drive, etc.. Specific please contact or online advisory contact.

2.1阀体材质，应以球墨铸铁，铸钢，不锈钢，316L为主，并注明牌号及铸铁实际的物理化学检测数据。

2.2阀杆材质，力求不锈钢阀杆(2CR13)，大口径阀门也应是不锈钢嵌包的阀杆。

2.3螺母材质，采用铸铝黄铜或铸铝青铜，且硬度与强度均大于阀杆。

2.4阀杆衬套材质，其硬度与强度均应不大于阀杆，且在水浸泡状况下与阀杆、阀体不形成电化学腐蚀。

2.5密封面的材质

①气动阀门类别不一，密封方式及材质要求不一;

②普通楔式闸阀，铜环的材质、固定方式、研磨方式均应说明;

③软密封闸阀，阀板衬胶材料的物理化学及卫生检测数据;

④蝶阀应标明阀体上密封面材质及蝶板上密封面材质;它们的物理化学检测数据，特别是橡胶的卫生要求、抗老化性能、耐磨性能;通常采用丁腈橡胶及三元乙丙橡胶等，严禁掺用再生胶。

2.6阀轴填料

①由于管网中的气动阀，通常是启闭不频繁的，要求填料在数年内不活动，填料亦不老化，长期保持密封效果;

②阀轴填料亦应在承受频繁启闭时，密封效果的良好性;

③鉴于上述要求，阀轴填料力求终身不换或十多年不更换;

④填料若需更换，气动阀设计应考虑能有水压的状况下更换的措施。

型号	Z6S41H-25	Z6S41H-16	Z6S41T-10
公称通径DN(mm)	50～600	40～400	40～400
适用介质	水、蒸气 、油品	水、蒸气	水、蒸气
最高介质温度(℃)	425	425	200
气缸工作压力(表)MPa	0.4～0.6

No Information

标准编号 标准中文名称 标准英文名称

ANSI/NFPA T 3.21.4 R2-2000 气动阀.NFPA/T 2.6.1 R2-2000补充件:液动元件压力额定值.检验疲劳和确定含金属外壳的液动气动阀的压力的碎 Pneumatic valve - Pressure rating supplement to NFPA/T2.6.1 R2-2000, Fluid power components - Method for verifying the fatigueestablishing the burst pressure ratings of the pressure containing envelope of a metal fluid power pneumatic valve

BS 4151-1967 输入信号为 3至151b/in压力计的气动阀定位器的评定方法 Method of evaluating pneumatic valve positioners with input signal of 3 to 15 lbf/in