According to the national standard "code for fire protection design of petrochemical industry > (GB50160-90) regulations," a fixed roof tank B liquid, application of flame arrestor and breather valve. Breather valve and flame arrestor are indispensable safety devices.
It can not only maintain the tank pressure balance, ensure the tank overpressure or vacuum in the rabbit when damaged, and can reduce the volatilization and loss in the tank. The tank pressure breathing valve is to maintain balance, reduce product safety and energy saving medium volatile, often associated with the use of flame arresters. The valve is mainly used for recycling pollution of the environment, endangering personal safety toxic and harmful gases.
1, storage: the above products are shipped to the site, if not installed or after the factory overhaul, rainproof facilities should be stored in a warehouse; emergency vent manhole series products not inverted during transportation.
2, maintenance:
A, the breathing valve series, the staff should be monthly on the tank top check, check valve plate, valve seat, valve stem, valve cover and other parts of any dust, dirt, if any, should be clean dry static; every six months, to the valve sleeve and the valve rod wipe of transformer oil.
B, each half staff should check the fire breathing manhole fire resistant layer at a time, if there is dirt, impurities clogging the fire resistant layer, fire resistant layer should be removed, remove stains with corresponding solvent, then rinse clean dry static fire resistant layer, put in ventilated dry and then put in the shell in.
C, more than the product shell inside and outside the surface of the paint should be re painted every year again.
壳体材质:碳钢、不锈钢(SUS304、SUS304L、SUS316、SUS316L)、衬氟、塑料。
内部芯件:阀盘、阀座、阀杆、阀套。
内部芯件材质:不锈钢或聚四氟乙烯。
密封圈材质:聚四氟乙烯。
阻火层材质:不锈钢。
环境温度:-40~+60℃。
我公司生产的呼吸阀,具有结构紧凑,通气量大,泄漏量小,耐腐蚀,密封性能好等特点.又开发了具有国际先进水准的防爆阻火器呼吸阀(HXF-IZ型),阻火器位于呼吸阀吸入口处,杜绝火源进入呼吸阀壳体内.具有体积小,重量轻,检修,清洗,更换方便等优点等特点。
阀盘采用聚四氟乙烯材料,具有耐低温,防冻等优点。阀内设静电输出装置,使得该阀时刻与罐体保持等电位。
操作压力:
A型:+355Pa(+36mmH20)、-295Pa(-30mmH20)
B型:+980Pa(+100mmH20)、-295Pa(-30mmH20)
C型:+1750Pa(+180mmH20)、-295Pa(-30mmH20)
D型:特殊压力,用户指定。
防爆级别:BS 5501:IIA、IIB、IIC。
在阻火呼吸阀正常工作情况下,阻火呼吸人孔基本保持密封状态,储罐处于正常压力。当呼吸阀正常工作满足不了因意外原因造成储罐急剧超压时,呼吸人孔的泄压盖自动顶开,进行紧急泄压,使罐内压力保持正常;当罐内压力急剧减压或超真空时,吸入阀便开启急剧吸入大气,维护罐内正常压力;当吸入大气带有火花、火焰时,阻火层起到“器壁效应”的作用来阻止火焰的通过,以保护储罐的安全。
法兰标准:GB、HG、SH、HGJ、JB、ANSL、JIS等标准。(用户指定,请注明压力等级)
制造、检测标准:按(石油储罐呼吸阀)SY7511-87、(石油储罐阻火器阻火性能和试验方法)GB5908-86等标准进行制造和验收;或用户指定标准。