ZSH Shanghai Valve Manufzcturing Co.,LTD.

Home > Products > Regulator valve > Fine small pneumatic film regulating valveZJHP

Description Material Performance Product Size Specifications

ZJHP (M) type single seat pneumatic (sleeve) by the pneumatic spring diaphragm actuator and low flow resistance through single seat control valve (valve sleeve valve), single seat valve body through single seat cover guide structure, as the plunger type valve structure, compared with the ordinary single seat valve has the advantages of small volume, light weight, characteristics applicable to the traffic flow and so on, leakage of demanding applications. Compared with the ordinary sleeve valve, the ZJHM type fine small sleeve has the characteristics of small size, light weight 1/3 and large flow 1/3, and is widely used in the automatic control system of the industrial process with low noise and large pressure difference.
Note: parameters are for reference only, or are not full. Valve can be used in accordance with the requirements of different pressure, material, diameter, drive, etc.. Specific please contact or online advisory contact.

valve body：

Body form: through single seat (sleeve) inverted S type casting type valve
Nominal diameter：DN20~300mm
Nominal pressure：PN1.6 4.0 6.4MPa
Connection type: flange typeJB78-59 JB/T79.2-94Concave type
Material Science：HT200 ZG230—450 ZG1Cr18Ni9Ti ZG0Cr18Ni12M02Ti
Upper valve cover: room temperature type.20~+200℃
Heat dissipation type40~+450℃
Packing: V type PTFE, flexible graphite, stainless steel bellows

Valve assembly:

Spool type: single seat guide (sleeve) plunger type valve

Flow characteristics: linear characteristics, such as the percentage of properties or fast opening characteristics
Material Science：1Cr18Ni9Ti 0Cr18Ni12Mo2Ti

Enforcement agencies：

Form: multi spring diaphragm actuator gasket: asbestos rubber sheet、1Cr18Ni9Ti
Diaphragm material: nitrile rubber reinforced with polyester fabric spring range： 20-100(40-200、80-240 、20-60
Compression spring：60Si2Mn 60-100) KPa
Push rod：2Cr13 Gas supply pressure：0.14 0.16 0.28MPa
Membrane cover：A3 Air source connector: internal screw threadM10X1
Bushing：2Cr13 Ambient temperature：-30~+70℃
Valve action type: gas one open, gas one off type

Nominal diameter(mm)	Valve seat diameter(mm)	Rated flow coefficient Kv		Rated travel(mm)	Effective area of filmcm2	Inherently adjustable ratio	ambient temperature℃	Basic error	Return difference	dead zone	Rated flow coefficient	Leakage rate
		straight line	Equal percentage
G3/4	3 4 5 6 7 8	0.08 0.12 0.20 0.32 0.50 0.80		10	220	50:1	-40~+85	Without positioner±5% Belt positioner ±1%	Without positioner ±3% Belt positioner1%	Without positioner±3% positioner0.4%	±10%	An 10-4 valve (10-3 valve sleeve, capacity rated capacity)
20	10	1.8	1.6	10	350
	12	2.8	2.5
	15	4.4	4
	20	6.9	6.3
25	25	11	10	16
40	32	17.6	16	25
	40	27.5	25
50	50	44	40
65	65	69	63	40	560
80	80	110	100
100	100	176	160
150	125	275	250	60	900
	150	440	400
200	200	690	630
250	250	1000	900	100	1400
300	300	1600	1440

ZJHP type single seat pneumatic control valve to allow pressure：

Switch mode	Actuator model	Spring range KPa	Gas pressure MPa	Nominal diameter (seat diameter)mm
Gas off				20				25	40	50	65	80	100	150	200
				10	12	15	20
	ZHA-22	20-100 20-100 40-200	0.14 0.25 0.4	6.4 6.4 6.4	6.19 6.4 6.4	3.96 6.4 6.4	2.2 6.4 6.4	1.4 6.4 6.4
	ZHA-23	20-100 20-100 40-200	-						0.56 3.64 5.04
	ZHA-34	20-100 20-100 40-200								0.35 2.30 3.18
	ZHA-45	20-100 20-100 40-200									0.34 2.21 3.06	0.22 1.43 1.98	0.14 0.91 1.26
Open air	ZHB-22	20-100 40-100 80-240	0.14 0.25 0.4	4.64 6.4 6.4	3.09 6.4 6.4	1.98 5.94 6.4	1.11 3.3 6.4	0.7 2.1 4.9						0.10 0.66 0.92	0.06 0.37 0.52
	ZHB-23	20-100 40-100 80-240							0.28 0.84 1.95	0.18 0.53 1.25
	ZHB-34	20-100 40-100 80-240									0.17 0.51 1.18	0.11 0.33 0.78	0.07 0.21 0.5
	ZHB-45	20-100 40-100 80-240												0.05 0.15 0.36	0.03 0.09 0.21

1、This table is based on the implementation of the standard specification. If the maximum working pressure exceeds the list range, to the present, take appropriate solutions.
2、This table is based on the valve closed position. Therefore, other locations will have a greater allowable differential pressure.

ZJHM type pneumatic sleeve control valve differential pressure gauge:

Switch mode	Actuator model	Spring range KPa	Gas pressure MPa	Nominal diameter（mm）
气关	ZHA-22	20-100 20-100 40-200	0.14 0.25 0.4	25	40	50	65	80	100	150	200
				3.00
				6.4
				6.4
	ZHA-23	20-100 20-100 40-200	0.14 0.25 0.4		2.25	1.95
					6.4	6.4
					6.4	6.4
	ZHA-34	20-100 20-100 40-200	0.14 0.25 0.4				2.36	2.04	1.67
							6.4	6.4	6.4
							6.4	6.4	6.4
	ZHA-45	20-100 20-100 40-200	0.14 0.25 0.4							1.41	1.14
										6.4	6.4
										6.4	6.4
气开	ZHB-22	20-100 40-100 80-240	0.14 0.25 0.4	1.50
				4.50
				6.4
	ZHB-23	20-100 40-100 80-240	0.14 0.25 0.4
					1.13	0.98
					3.38	2.93
	ZHB-34	20-100 40-100 80-240	0.14 0.25 0.4		6.4	6.4	1.18	1.02	0.84
							3.54	3.06	2.51
							6.4	6.4	5.85
	ZHB-45	20-100 40-100 80-240	0.14 0.25 0.4							0.71	0.57
										2.12	1.71
										4.94	4.00

Description: 1, the table to the Standard Specification for the implementation of the implementation of the foundation. If the maximum working pressure exceeds the list range, to the present, take appropriate solutions.

Nominal diameter	L(mm)			H(mm)		H1(mm)				ФA(mm)
Nominal diameter	ANSI125FF ANSI150RF JIS10KFF.RF PN0.6、1.6	ANSI300 JIS2030KRF PN4.0	ANSI600 JIS40K.RF PN6.4	ordinary	high temperature	PN6	PN16	PN40	PN64	ФA(mm)
G3/4″	120	120	120	253		31	31			236
20	181	194	206	398.5	548.5	45	52.5		65	285
25	184	197	210	410.5	560.5	50	57.5		70
40	222	235	251	455	620	65	75		85
50	254	267	286	457.5	627.5	70	82.5		90
65	276	292	311	610	790	80	92.5		102.5	360
80	298	317	337	622	8.7	95	100		107.5
100	352	368	394	640	850	105	110	117.5	125
150	451	473	508	870	1130	132.5	142.5	150	172.5	470
200	600	610	650	890	1150	160	170	187.5	207.5	470

Flange connection size

The flange connection of product size in line with national standards, GB9115.988, PN64 with JB7959 GB9115.788. The connection of the old product size and the JB7859 "cast iron flanges", connecting dimensions JB7959 "" in the cast iron flanges are basically the same, can be applied to replace the installation does not affect and old products.

JISB2001－1984
ANSIB16.5－1981
Flange connection：FF、PR、RJ和LG。